Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Walk-In Showers & Shower Remodeling in Richmond Heights, FL: What the Job Actually Takes
A walk-in shower remodel in Richmond Heights, FL runs $9,000 – $28,000 for a full custom tile build with new waterproofing, drain, pan, glass, and fixtures, and most projects take six to ten working days once demolition starts. Standalone shower replacement lands lower, at $3,000 – $8,500, while a zero-threshold build with frameless glass and premium fittings pushes toward the top of the range. Call (844) 761-9356 and we’ll walk your Richmond Heights bathroom and put real numbers against it.
How the Work Unfolds, Day by Day
Walk-in showers & shower remodeling is a sequence, not a weekend swap. Here’s exactly what happens and when, so you can plan around it.
Day 1: Demo and discovery
We tear out the old tile, pan, and valve trim, then open the wall enough to inspect what’s behind it. In Richmond Heights, that inspection matters, because mid-century block walls and older copper or galvanized supply lines don’t always match the drawing. By end of day you know whether the existing framing is straight and whether any structural or plumbing surprises will change the scope. This is the point where a homeowner confirms the final tile and trim direction so material orders can release.
Days 2 – 3: Rough-in and waterproofing
New valve, drain, and any plumbing relocations get set, followed by backer board and a bonded waterproofing membrane on the pan and walls. The membrane is the whole ballgame in this climate. It goes down as a continuous system, not painted-on afterthought, and it has to cure flat and slope correctly toward the drain before a single tile is set. A municipal rough inspection usually gets scheduled here if the permit scope calls for one.
Days 4 – 6: Tile and setting
Large-format floor tile, wall tile, niche trim, and the bench or curb detail go in over the membrane. Grout lines get sealed after curing. Homeowners decide vein direction on natural stone and grout color at this stage, both of which are harder to change later than people expect.
Days 7 – 9: Glass, fixtures, and finish
Frameless glass panels are templated after tile is fully set, then installed, followed by the showerhead, handheld, drain cover, and any grab bars or shelving. Kohler and Moen valve and trim packages are the most common choices here. A licensed glass fabricator measuring after tile, not before, is the difference between a clean sightline and a shimmed mess.
Days 10 – 12: Final inspection and walkthrough
If the permit required inspections, they clear here. We run a full water test on the drain and pan, check the valve for leaks, and do a joint walkthrough with you. Any punch-list item goes on paper with a date. The 730-Day Done Right Promise starts at this handoff.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
The decisions that move both the price and the feel of a walk-in shower fall into a handful of real categories. Here’s the honest trade-off on each.
- Zero-threshold vs. low curb. A zero-threshold shower is flush with the floor, accessible, and looks cleanest, but it requires the floor to be sloped and re-framed during rough-in and can push the job $1,500 – $3,000 higher. A low curb (2 to 4 inches) is cheaper and installs faster, and works fine for most households. If anyone in the home has mobility needs, zero-threshold is the long play.
- Tile choices. Porcelain or ceramic slab tile is durable, easy to seal, and the most forgiving in Florida humidity. Natural stone like marble or travertine looks richer but is porous and needs re-sealing every year or two. Silestone and Caesarstone tend to come up more on the vanity top than the shower floor, but their matching wall panels are a real option for people who want zero grout lines.
- Glass. Frameless glass is the premium look: no frame to collect mildew, wider opening sightline, but it runs $1,200 – $3,000 more than framed and needs precise templating after tile set. Framed glass is a solid budget choice and holds up well when the homeowner is doing a rental-grade refresh.
- Bench, niche, and curb details. A built-in tile bench adds about $800 – $1,800 and makes the shower usable for grandkids and older family members. A recessed niche is $200 – $600 and always worth it. Skip the curb-to-ceiling glass and use a half-wall if you want some privacy and lower glass cost.
- Showerheads and valves. A standard Moen or Kohler pressure-balance valve handles most homes. A thermostatic valve with multiple showerheads or a rain head runs $400 – $1,200 more in parts and labor, and it needs adequate water pressure at the supply.
What Walk-In Showers & Shower Remodeling Costs in Richmond Heights, FL
The realistic range for this job in Richmond Heights is $9,000 – $28,000. That covers a curbless or low-curb walk-in shower with a bonded waterproofing system, tile on walls and floor, frameless or framed glass, a new valve and trim, and finish work. Outside a few premium builds, that number rarely lands much lower or higher in this market.
What pushes a job toward the bottom of the range:
- Existing plumbing stays put. Keeping the drain and valve where they are avoids opening the slab or re-framing the wall.
- Tile grade. Porcelain is the standard; natural stone and slab panels raise both material and install time.
- Glass scope. Framed glass is cheaper; a frameless single panel with a door is the most expensive single line in the job.
- Size. A 36-by-48-inch shower with a single glass panel is cheaper than a 60-by-60 with a bench and two panels.
- Permit scope. If the plumbing rough-in isn’t moving, you often only need the shower permit, not a full bath re-pipe.
Every written estimate lists the tile, glass, valve, prep, and permit fees line by line. The quoted number is the number you pay on a fixed-scope job. Change orders only happen if a hidden condition emerges during demo, and you get the price and the decision before work moves forward.
See the difference
Before
After
Before
After
Before
AfterWhat Richmond Heights Homes Do to This Job
Richmond Heights is a ZIP 33176 community of mid-century concrete-block ranch homes sitting on a ridge that once saw hard-rock mining and canal work, and that geology shows up in this trade every week. The limestone bedrock and the area’s high water table mean any shower slab work has to be planned around what’s under the surface, and any addition or structural tie-in can hit rock sooner than in neighboring Kendall or Pinecrest. Crawl the older homes and you’ll find galvanized supply lines in some and copper in others, plus additions from later decades that changed the bathroom footprint.
Richmond Heights permitting runs through Miami-Dade County, and shower remodels that move a drain or valve need a plumbing permit and rough inspection. We pull it, we pass it, and we show you the signed-off paperwork. The county’s hurricane code also drives tie-downs on any wall we open, and impact-rated glass in bathrooms with windows. Local 1950s to 1970s ranch homes often have terrazzo floors, and that affects how the shower pan meets the slab. When a shower connects to a larger project, homeowners sometimes pair it with Roof Replacement & Installation in Richmond Heights or Metal Roofing in Richmond Heights while we’re already on site. Our crews also cover the rest of Richmond Heights and the surrounding blocks.
Serving Richmond Heights, FL – Our Local Coverage Area
We serve Richmond Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Walk-In Showers & Shower Remodeling in Richmond Heights
Most walk-in showers & shower remodeling projects in Richmond Heights take six to twelve working days, from demo to final walkthrough. Rough-in plus waterproofing sets the two-to-three-day front end; tile and glass fill in the rest. If the permit requires a rough inspection, add two to four days of scheduling around it.
Yes, if the drain or valve moves, you need a plumbing permit through Miami-Dade County. If the shower pan is rebuilt at the same location with no plumbing changes, a shower permit is still usually required because the waterproofing and pan replacement are permitted work. We handle the filing and the inspection. Call (844) 761-9356 and we’ll confirm the exact scope for your address.
Yes, and most Richmond Heights homeowners do exactly that. Keeping the existing shower footprint and drain location avoids slab cuts and re-framing, which keeps cost closer to the low end of $9,000 – $28,000. The tile, glass, and waterproofing still come out completely new.
Expect $9,000 – $28,000 for a full custom walk-in build in Richmond Heights, or $3,000 – $8,500 for a shower replacement that reuses the existing footprint. Frameless glass, natural stone, a bench, and a zero-threshold pan push the number higher. Estimates are free and itemized.
Every walk-in shower we build is covered by the 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. That covers waterproofing, tile set, glass installation, and plumbing connections we installed. If something isn’t right within two years, we make it right.
Get a Free Estimate on Walk-In Showers & Shower Remodeling in Richmond Heights
Call (844) 761-9356 to schedule your free on-site estimate for walk-in showers & shower remodeling in Richmond Heights. We measure the space, talk through zero-threshold versus low-curb, lay out tile and glass options, and hand you a written line-item quote before you commit. The 730-Day Done Right Promise is standard on every job, and calls are answered live around the clock.
Written by the team at Groundwork Construction Co.