Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sliding & Patio Doors in Richmond Heights, FL: What the Job Actually Involves
Sliding and patio door replacement in Richmond Heights, FL typically runs $2,400 to $9,500 per opening, and most single-door swaps take one to two days once the unit is on site. You’re replacing a large glazed opening, not just a panel: track, threshold, frame, glass, and the flashing that keeps our summer downpours outside where they belong. Custom and oversized units in Richmond Heights’s newer infill builds push toward the top of that range. Call (844) 761-9356 for a free on-site measure and a written, line-item estimate.
How We Install Sliding & Patio Doors, Stage by Stage
Every job follows the same five-stage sequence, whether it’s a 1950s ranch on a slab or a 2020s custom build. Here’s what happens and when.
1. Measure, scope, and written estimate (day 0)
We measure the rough opening, check the existing frame for rot and settlement, and confirm the door swings or slides the way you need. You get a written quote with the unit, glazing package, finish, and labor broken out, so you can compare apples to apples. Your decision here: impact-rated glass or standard, and whether you’re keeping the opening or reconfiguring it.
2. Order and lead time (2 to 6 weeks)
Impact glazing and custom sizes carry longer lead times than stock units. We confirm the delivery date in writing before we schedule the install. Your decision: which finish and hardware package you want, since those add lead time too.
3. Demo and prep (day 1, roughly 4 to 6 hours)
We pull the old door and frame, inspect the rough opening for water intrusion and rot, and repair the framing if needed. On slab homes, we check the threshold for proper slope and drainage before anything goes back in. Your decision: whether we address any rot found during demo now or in a follow-up visit.
4. Install, flash, and seal (day 1 into day 2)
The new unit goes in level and plumb, with flashing and sealant at the threshold, jambs, and head to shed water away from the wall. On impact units, we set the anchors to code for the opening and your home’s construction. Your decision: interior trim detail, if you’re replacing it.
5. Inspection and final walk (day 2 into day 3)
We test the slide, the lock, and the screen; then we walk the job with you. If the permit requires a final inspection, we schedule it and confirm in writing that it passed. Your decision: nothing at this point except signing off, which is the way it should be.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Sliding & Patio Door Options You’ll Choose Between
- Impact-rated sliding glass doors: The standard for Richmond Heights. They hold up to hurricane wind and debris, meet code, and often qualify for insurance credits. The trade-off is cost and weight, plus a slightly heavier feel on the track.
- Standard or non-impact glass: Noticeably less expensive, suited to a screened porch or interior pass-through where windborne debris isn’t a concern. It doesn’t meet impact code for exterior openings.
- Multi-slide and pocket doors: Panels that stack or disappear into the wall, opening a whole patio wall to the yard. Custom sizing and pocket framing push cost up, but for a Richmond Heights home with a large lanai, nothing else opens the space the same way.
- Frame material: Aluminum is light and won’t rot, but it conducts heat; thermally broken aluminum or vinyl/composite frames are better for our climate. Wood frames offer the premium look some Richmond Heights custom homes call for, at a higher price and with more maintenance.
- Hardware and finish: Stainless rollers, soft-close tracks, and multi-point locks are worth the upgrade on a door you’ll use every day. Finish choices range from standard anodized to custom powder-coat.
What Sliding & Patio Doors Cost in Richmond Heights, FL
Most sliding and patio door projects in Richmond Heights land between $2,400 and $9,500 per opening. Here’s what moves the number.
| Job type | Typical range |
|---|---|
| Stock slider, standard glass, similar-size swap | $2,400 – $4,200 |
| Impact-rated slider, stock size | $4,000 – $7,000 |
| Custom or oversized impact slider | $6,500 – $9,500 |
| Multi-slide or pocket door system | $9,500+ |
What pushes you to the high end: custom sizing, impact glazing, a reconfiguration that requires new framing or a header, rot found at demo, and permit scope. What keeps you low: a stock size that fits the existing opening, standard glass on a screened opening, and a clean rough opening with no rot.
Your written estimate itemizes the unit, glazing, labor, disposal, and permit cost. It does not include unexpected structural repair found during demo; we photograph it and quote it before proceeding, never after.
See the difference
Before
After
Before
After
Before
AfterWhat Richmond Heights Homes Specifically Do to This Job
Richmond Heights is one of South Florida’s historically Black communities, and its housing tells the story: 1950s to 1970s concrete block ranch homes on slabs with terrazzo floors, mixed with a wave of new infill construction as older lots get redeveloped. That mix matters here. On the older ranches, we frequently find settled threshold framing and past water intrusion at the patio opening, especially where the original door has been patched and re-caulked for years. On the newer builds, the rough opening is often engineered for a specific unit, so the measure and the anchor detail have to match. The high water table and summer downpours mean threshold drainage and flashing get checked before anything goes in. And because the limestone bedrock sits close to the surface in Richmond Heights, we plan for it if the opening needs structural work.
Serving Richmond Heights, FL – Our Local Coverage Area
We serve Richmond Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Sliding & Patio Doors in Richmond Heights
A single stock slider takes one to two days; custom or multi-slide systems can run two to three days if framing or reconfiguration is involved. Lead time for the unit itself is the bigger variable, so call (844) 761-9356 to get a realistic timeline for your opening.
In most cases, yes: an exterior door replacement that changes the opening or involves structural or impact-code compliance requires a permit in Richmond Heights. We pull the permit, schedule the inspection, and confirm the pass in writing. Call (844) 761-9356 and we’ll tell you exactly what your job needs.
Yes, if the new unit fits the existing rough opening. A same-size swap avoids framing work entirely. If you want to widen the opening or switch to a multi-slide, that requires a header and structural work we scope and quote upfront. Call (844) 761-9356 for a free measurement.
Most jobs run $2,400 to $9,500 per opening depending on size, glazing, and whether the opening is reconfigured. Call (844) 761-9356 for an exact quote; estimates are free.
Labor and installation are covered by our 730-Day Done Right Promise, and the door manufacturer’s warranty covers the unit and glass. We hand you both in writing at the final walk. Call (844) 761-9356 with questions before you buy.
Get a Free Sliding & Patio Door Estimate in Richmond Heights
Call (844) 761-9356 to schedule a free on-site estimate for sliding and patio doors in Richmond Heights. We’ll measure the opening, walk you through impact versus standard glazing, and hand you a written, line-item price before you commit. Calls are answered by a live person 24/7, and every project is backed by our 730-Day Done Right Promise. That’s it. No pressure, no surprises.
Written by the team at Groundwork Construction Co.