Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Tamiami, FL: What the Job Actually Involves
Custom and geometric windows in Tamiami run $9,440 to $29,500 installed, and most homes need six to ten weeks from signed contract to final inspection because every arched, angled or trapezoid unit is made to order and has to clear Miami-Dade product approval before it ships. A single feature window can be measured and set in about three weeks. Call (844) 761-9356 to book a free on-site estimate and get a written, line-item number for your openings.
How custom and geometric windows get built here, stage by stage
These aren’t stock units pulled off a shelf. Half the work happens before anything is ordered, and the sequence matters more than the schedule.
Day 1: Measure and template
We template every opening on site – arches get a physical pattern, angled units get plumb and level readings at four points. This is where the homeowner picks frame material, glass package and finish color, because those choices lock the order. Skipping a proper template on a radius window is how you end up with a $12,000 mistake that can’t be trimmed to fit.
Weeks 2 to 5: Permit drawings and product approval
In unincorporated Miami-Dade, the permit package has to show a Miami-Dade NOA (Notice of Acceptance) for the specific window product, plus wind-load calculations for the design pressure at your opening. For an arched or trapezoid window, the manufacturer’s approval document has to cover that shape, not just the rectangular system. Plan on two to four weeks for review, longer if the plan reviewer asks for a stamped correction.
Fabrication: four to six weeks
This is the long pole. Geometric shapes are built one at a time. Radius and true-arch units typically run four to six weeks; simple eyebrow or half-round shapes can come in faster. The homeowner should confirm glass package and grille pattern in writing during this window, because once fabrication starts, changes are a new order.
Installation: one to three days
Most custom and geometric window packages on a Tamiami home go in over one to three days depending on count and elevation. We pull the old units, check for rotted framing or failed flashing at the rough opening, set the new windows with the specified anchors, and seal per the approval drawings. Any hidden rot or rusted lintel gets flagged the same day, with a written price before we touch it.
Final inspection and closeout
A Miami-Dade inspector signs off on the anchors, flashing and label placement, and the homeowner gets the permit record plus the manufacturer’s warranty paperwork. We follow up with a walk-through to check operation and weatherstripping on every unit, then the project sits under the 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Custom shapes narrow the field fast, so knowing the trade-offs up front saves weeks of back-and-forth.
- Aluminum frames with impact glass: the workhorse for Tamiami homes. Strong, holds up to salt-humid air, and the cost per opening sits in the middle of the range. Finishes are usually baked or anodized, and while the palette is broad, it isn’t endless.
- Vinyl frames: the value pick on small geometric units like half-rounds over a front door or an octagon accent. Fine thermally, but the frame walls are thicker, so sightlines get chunky on a big feature window and the glass area shrinks.
- Wood-clad or wood interior: the premium look for a dramatic two-story arch or a custom great-room wall. Materials like Andersen or Marvin give real finish choices inside and a low-maintenance exterior, but expect the higher end of the range and a longer fabrication timeline.
- Glass packages: impact-rated laminated glass is basically the entry ticket under HVHZ rules. Upgrading to low-E or a specific solar-control tint helps on the west-facing sun here, but adds cost per square foot.
- Door openings that complete the set: a front entry or slider in the same system is common. Therma-Tru and Mr-Glass products show up often on that part of the job because finish and frame color can match the windows.
- Grille and finish style: simulated divided lites, color-matched trim and interior casing all drive cost. A single custom radius grille pattern is a fabrication line item, not a paint choice.
What Custom & Geometric Windows costs in Tamiami, FL
Expect $9,440 to $29,500 for a custom and geometric window package on a typical Tamiami home, with a single feature window at the low end and a whole-house custom set at the top. The opening count and shape complexity are the biggest levers, followed by frame material, glass package and how much rot or past unpermitted work has to be corrected first.
What pushes a project toward the high end: true radius and arched units (each is a custom fabrication run), wood-clad interiors, whole-house scope, and correcting a rough opening that wasn’t built to the right dimensions. A clean, single-half-round replacement stays near the bottom of the range.
A written estimate should list each opening by size and shape, the frame material and finish, the glass package, the permit and inspection fees, and the labor – nothing bundled into a lump sum. What’s typically outside the estimate: structural framing repair if a lintel or header is compromised, interior drywall and paint touch-up, and stucco patching around the exterior perimeter. We flag those the moment we see them and price them in writing before any work proceeds.
See the difference
Before
After
Before
After
Before
AfterWhat Tamiami homes specifically do to this job
Nearly every block home here sits inside Miami-Dade’s High Velocity Hurricane Zone, so every custom and geometric window has to carry product approval for that exact winding and meet wind-borne-debris and impact standards – design trends don’t get a vote. The 1970s and 1980s concrete-block ranches off SW 8th Street and the low-rise townhome clusters along that corridor often carry unpermitted Florida rooms and patio enclosures left by prior owners. When a geometric window lands on one of those walls, we routinely have to legitimize or remove the prior work before the new scope can pass inspection, and that changes the timeline and the price. Salt-laden humid air eats at fasteners and flashing, and the near-daily summer thunderstorms make water-intrusion detailing the difference between a window that holds for decades and one that leaks after the first June storm. We cover all of Tamiami, including the 33184 ZIP, and the same wind-load reality applies to neighbors in Westwood Lakes, Kendale Lakes, Sunset and Kendall West.
Serving Tamiami, FL – Our Local Coverage Area
We serve Tamiami and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Custom & Geometric Windows in Tamiami
Plan on six to ten weeks from signed contract to final inspection, with the bulk of that in permit review and product fabrication. Installation itself is usually one to three days. Call (844) 761-9356 for a free estimate and a realistic timeline for your openings.
Yes. Any window change here requires a Miami-Dade permit, and if the wall opening is enlarged or relocated you may also need an engineer’s letter or revised drawings. We pull the permit and see it through inspection, so you’re not chasing paperwork. Call us to talk through what your project will need.
In most cases, yes – a retrofit into the existing framed opening leaves the structure alone. But if the opening is undersized, out of square, or sitting on unpermitted prior work, we’ll need to correct the framing first, and that’s where scope grows. An on-site look is the only way to know for certain.
True radius and arched shapes, wood-clad interiors, whole-house scope and hidden rot or past unpermitted work are the four biggest drivers. A single standard half-round replacement stays near $9,440. Call for an exact quote – estimates are free.
The window units carry the manufacturer’s warranty, and all the installation work falls under our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space. Call (844) 761-9356 to ask how it applies to your job.
Get a free estimate on Custom & Geometric Windows in Tamiami
Call (844) 761-9356 for a free on-site estimate on custom and geometric windows in Tamiami. A live person answers, day or night. We’ll template the openings, walk you through frame and glass choices, and hand you a written line-item quote with the permit fees itemized, backed by the 730-Day Done Right Promise. This is often part of a full Windows & Doors in Tamiami scope, and if you’re updating the exterior at the same time, homeowners often pair this with Concrete Driveways & Concrete Work in Tamiami or Asphalt Driveways & Resurfacing in Tamiami. You can see the whole Windows & Doors service here.
Written by the team at Groundwork Construction Co.