Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CertainTeed Bathroom Remodeling: The The Hammocks Owner’s Guide
We install CertainTeed bathroom systems and the trim, backer, and moisture-management components that go with them in The Hammocks, and a full bathroom remodel here typically runs $9,000 – $28,000 depending on tile, shower configuration, and whether the subfloor and framing need work. CertainTeed is best known on our jobs for gypsum, tile backer, and moisture-resistant board rather than the fixtures themselves, so when an owner tells us their “CertainTeed bathroom” is failing, they usually mean a board, membrane, or panel is soft, stained, or letting grout crack above it.
The tell is often a hairline crack in grout that keeps coming back, a hollow sound when you press on a shower wall, or a soft spot at the bottom edge of a board near the tub. In The Hammocks, that pattern shows up most after a wet season, when a slow leak behind tile has had three or four months of the rainy season to spread.
Key Takeaways
- Installed bathroom remodel pricing in The Hammocks: $9,000 – $28,000.
- Most CertainTeed failures we see are moisture-related board or membrane failures, not tile failures.
- We are an independent service provider, not affiliated with CertainTeed. We install and replace their products, we don’t manufacture or sell them.
- Our technicians have up to 12 years of experience, and every project is backed by the 730-Day Done Right Promise.
Which CertainTeed Models This Applies To
CertainTeed’s bathroom-relevant lineup is broader than most owners realize. The names you’ll see on a label or on the substrate behind your tile include GlasRoc (moisture- and mold-resistant gypsum board), Diamondback tile backer, SilentFX acoustic board (occasionally used in shared walls), and AirRenew board. If your project is older or the previous remodel used a contractor’s standard stock, there’s no CertainTeed label on the backer at all, and that’s fine – what matters is matching the right replacement spec.
The way to identify the correct part is by thickness, width, and edge profile, not by guessing from a photo of tile. GlasRoc and similar boards come in 1/2″ and 5/8″ thicknesses, and 1/2″ is the most common for walls while 5/8″ shows up where a heavier tile load or impact spec is needed. Measure the board edge at a cut, check for a printed label near the seam, and note the width (48″ is standard). Then decide OEM vs. aftermarket: for moisture-critical work, matching the CertainTeed board spec exactly avoids warranty questions and gives you a known paperless face and moisture-resistant core. On a straightforward cosmetic patch behind dry areas, a quality equivalent from a major manufacturer is often fine – we walk you through which side of that line your project sits on.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CertainTeed Bathroom Remodeling Is Failing
- Grout cracks that return after you seal them. Movement in the substrate, or a board that’s absorbed moisture and begun to swell, is flexing the tile above it. Sealing the grout fixes the look, not the cause.
- A hollow sound when you tap the shower wall. Tap gently with a knuckle across the wall. A dead, hollow thud where you’d expect a solid sound usually means the board has separated from the stud or lost adhesion behind it.
- Soft or crumbly board at the tub edge or bottom seam. This is the classic GlasRoc and Diamondback failure pattern we see in The Hammocks, where a slow tub-overflow leak feeds the bottom edge for months before it shows up as a stain.
- Musty smell that comes back after cleaning. Odor returning within days of a deep clean often points to moisture trapped behind the tile or under the floor, not a surface mildew problem.
- Tiles popping loose or lipping at the seams. Tiles that lift or rock underfoot mean the setting bed has lost bond, which traces back to substrate movement or a wet board that never should have stayed wet.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed bathroom remodel pricing in The Hammocks runs $9,000 – $28,000, and a targeted shower rebuild or board-and-tile replacement is a smaller slice of that. Here’s how the pricing breaks down for the work most owners land on:
| Scope | Installed Range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement (tile and board only) | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What drives the range: whether the subfloor and studs are sound or need replacement, tile size and pattern (large-format tile is faster to set but less forgiving on a wavy substrate), and whether the existing plumbing needs to move. Our quotes are line-item and upfront, so board, setting materials, tile, and labor are each spelled out. Work is covered by our 730-Day Done Right Promise.
DIY or Call Us?
There’s a safe middle ground and a hard line. On the safe side: measure your board thickness at a cut edge, tap walls to check for hollow spots, check for leaks at the tub and shower valves, and photograph everything for the quote. Homeowners can also re-caulk tub-to-wall seams and refresh grout as routine maintenance.
Where DIY goes wrong: tearing out a tile wall to “just replace the board” almost always uncovers wet framing or a missed leak at the valve or drain, and that’s a job for someone who can read what they’re finding. If the board is soft or the leak source isn’t obvious, stop after the inspection. Call (844) 761-9356 to schedule your free estimate. Most jobs start with a same-visit assessment so you’re not guessing at scope.
FAQs
With a properly sealed shower and the right board spec, expect 15 – 25 years in a well-ventilated bathroom. In The Hammocks’ humid summers, the limiting factor is almost always ventilation and leak repair, not the board itself. A board that stays wet for a season will fail early regardless of brand.
Sometimes yes. A localized patch on a sound substrate is a reasonable repair if the moisture didn’t spread. If the leak is at the valve, drain, or behind the tub, or if two or more wall panels are soft, full replacement is the honest answer. We’ll tell you which side you’re on during the estimate.
A shower board-and-tile replacement typically takes 3 – 5 working days on a standard bath, and a full remodel runs 2 – 4 weeks. The time depends on whether tile is being set (curing time matters) and whether subfloor work is needed. Most jobs are completed in a single visit for the assessment and demo, then scheduled for tile.
We source CertainTeed-compatible board through our brand-partner network and match the spec to your project – no guessing, no stock substitution. We also work with KraftMaid, Cambria, and Silestone on the cabinetry and countertop side of a bathroom. Call (844) 761-9356 for a free estimate and a clear line-item quote.
Written by the team at Groundwork Construction Co. of The Hammocks, serving The Hammocks and nearby areas.