Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Kendale Lakes, FL: What It Costs and How Long It Takes
An iron fence in Kendale Lakes runs $3,500 – $9,000 for a typical single-family lot, and most jobs take two to four days on site once the layout and finish are locked. You’re buying a welded steel or wrought-iron system set in concrete footings, not a kit that rattles loose in a storm. Call (844) 761-9356 and we’ll walk your property line and price it in writing.
How We Build an Iron Fence in Kendale Lakes, Stage by Stage
An iron fence is mostly a footing job that happens to end in metal. The panels go up fast. What takes time is layout, digging, and cure. Here’s the real sequence.
- Stage 1 – Site walk and layout (about an hour, day of estimate). We mark the actual property line against your survey, note where the concrete driveway apron, pool cage, or screened lanai meets the run, and flag any irrigation lines or buried conduit. You decide the height (4 ft, 5 ft, or 6 ft), the picket spacing, and whether gate posts get set deeper for a swinging gate. This is also where we confirm whether the run crosses a swale, because drainage easements along the Kendall canals change where posts can legally land.
- Stage 2 – Utility locate and demo (half a day). Sunshine 811 marks the public utilities before anyone digs. If there’s an existing wood or chain-link fence, we pull it and haul it off. On most Kendale Lakes lots the old fence is 20-plus years old and half-buried in roots, so plan on a morning for removal alone.
- Stage 3 – Footings (day one into day two). Posts go in 24-inch-deep, 10-to-12-inch-diameter concrete footings, set below grade and crowned so water sheds away. This is non-negotiable in Miami-Dade’s sandy fill and high water table: shallow footings lean within a season. You decide now whether you want the concrete visible or mounded and sodded over. Cure takes 24 to 48 hours before panels go on.
- Stage 4 – Panel and gate hang (day two or three). Rails weld or bolt to posts, pickets align, and the gate gets its hinges, latch, and closer. You sign off on gate swing direction and latch height here, because changing it after welding means cutting and re-powder-coating.
- Stage 5 – Finish and final walk (same day). We touch up field welds with matching coating, clean up, and walk the run with you. You get the workmanship document in hand that day.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make on an Iron Fence
Two decisions drive most of the cost and all of the longevity: what the metal is, and how it’s protected. Getting either wrong in South Florida humidity shows up as rust within three or four years.
- Material grade. Solid wrought iron (true puddled iron) is rare and expensive now. What you’ll mostly choose between is pressed-steel ornamental panels, which run $3,500 – $6,000 installed and give you a clean traditional look, and heavier hot-rolled steel or aluminum-cast systems at $6,000 – $9,000 that hold up better to impact and take a gate without sagging.
- Finish and coating. Powder-coat over galvanized steel is the standard for our climate and holds color for a decade or more. Bare or thin-painted steel will flash rust on welds and scratch points. If the fence is within salt-spray distance of the coast, we spec a heavier galvanized basecoat.
- Picket style and spacing. Spear-top vs. flat-top, 4-inch vs. 6-inch spacing. Tighter spacing looks better and costs more per linear foot. Vertical pickets meet most Miami-Dade pool safety sightline requirements better than horizontal rails.
- Height and configuration. 4 ft reads as decorative and keeps pets in. 5 to 6 ft is a real barrier for privacy and pool code. Each foot of height adds roughly 15 – 20% to material cost.
- Gates and automation. A single walk gate is standard. A drive gate with a swing operator adds real cost and requires a power drop at the post, which we plan in Stage 1.
- Accent and finish color. Black is standard. Bronze and custom colors are available and worth it if the fence sits against a lighter CBS stucco wall.
What an Iron Fence Costs in Kendale Lakes, FL
For a typical 33183 lot, plan on $3,500 – $9,000 for the fence itself, with a median job in the low-to-mid $5,000s. Here’s where that number moves:
| Line Item | Typical Range |
|---|---|
| Pressed-steel ornamental fence, installed | $3,500 – $6,000 |
| Hot-rolled steel / cast iron system, installed | $6,000 – $9,000 |
| Walk gate (single) | Included to +$600 |
| Drive gate with operator and power drop | Add $1,500 – $3,500 |
| Old fence removal and haul-off | Add $250 – $700 |
| Heavier galvanized basecoat (coastal exposure) | Add 8 – 15% |
What moves a job to the high end: total linear footage over 150 ft, running over an existing concrete apron or pool deck (which means coring rather than digging), tight property lines that require hand-digging near a survey marker, and gates. What keeps it at the low end: a straight run on open lawn, a standard 4 ft pressed-steel system, and no gate automation.
What’s in every written estimate: footing spec, post spacing, coating, gate hardware, haul-off, and the workmanship term. What’s not: landscape repair after digging, sod replacement where footings were crowned, and any HOA fees for architectural review. We list those separately so the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Kendale Lakes Homes Specifically Do to an Iron Fence Job
Kendale Lakes is a build-out Kendall subdivision, ZIP 33183. Almost every job here is redoing a 1970s-to-1990s CBS home with stucco walls, not a greenfield build. That matters for an iron fence in two specific ways. First, most properties already have a fence line that’s been through one or two replacements, and the old footings are still in the ground. We’re often pulling a buried wood post out of the exact spot the new steel post needs to go. Second, because these are small lots in a dense subdivision, the fence line frequently runs tight against the screened lanai, the pool cage, and the concrete driveway apron, so a fair share of the job is hand-digging rather than machine digging. If you’re planning the fence as part of a full Fence Installation in Kendale Lakes project, the layout works best when it’s drawn at the same time as the rest of the yard plan.
Miami-Dade’s post-Andrew wind code and the county’s structural inspection regime shape the work too. Any iron fence on a lot where a garage-to-room conversion or an addition already happened needs the fence line checked against the survey, because postholes near a converted slab sometimes hit old footings or conduit that was never redrawn. And the county’s HOA and easement rules are real: many of the subdivisions that feed 33183 have architectural review boards, and the Kendall canal-adjacent lots carry drainage easements that legally restrict where you can set a fence. That’s why our layout walk is first, not last. We cover Kendale Lakes regularly, so we know what the inspectors and the review boards here expect.
Serving Kendale Lakes, FL – Our Local Coverage Area
We serve Kendale Lakes and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Iron Fence in Kendale Lakes
Two to four days on site for a typical single-family run, with footing cure accounting for one to two of those days. Larger runs over 150 ft, gates with operators, and jobs that require demo of an old fence push toward the four-day end. Call (844) 761-9356 for a timeline based on your actual lot.
In most cases, a fence under the height limit on your own property line does not require a building permit, but Miami-Dade’s rules and the subdivision’s architectural review do apply, and any fence that touches a drainage easement has its own constraints. We confirm the specifics for your address before we set the layout. Call (844) 761-9356 and we’ll tell you what your lot requires.
$3,500 – $9,000 installed, depending on material grade, total footage, whether you add a drive gate, and whether an old fence needs to come out. The range covers most 33183 lots; the final number depends on your property line. Call (844) 761-9356 for an exact quote in writing, no charge.
Not if the layout and material are locked before Stage 3. Our written estimate holds. The one variable that can shift it is finding buried conduit, old footings, or a utility line the locator didn’t flag, and we handle that with a written change order you approve before any work continues, never a surprise on the final invoice. Call (844) 761-9356 to talk through your lot.
Every install carries our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on footings, panel alignment, gate operation, and coating application. Call (844) 761-9356 to ask what’s covered on your specific install.
Get a Free On-Site Estimate for Your Iron Fence
Every iron fence project in Kendale Lakes starts the same way: a free on-site estimate where we walk the property line, confirm the layout against your survey, and hand you a written line-item price with the footing spec and material grade spelled out. Call (844) 761-9356 to book it. A live person answers, every time. If you’re also redoing the pool deck or driveway while the fence goes in, homeowners often pair this with Patios, Walkways & Pool Decks in Kendale Lakes, or plan it alongside ADU Design & Permitting in Kendale Lakes if a backyard build is on the table. For the broader scope, see our Fence Installation service.
Written by the team at Groundwork Construction Co.