A Groundwork company - serving The Hammocks, FL
M

Mr-Glass Kitchen Remodeling in The Hammocks, FL

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Mr-Glass Kitchen Remodeling in The Hammocks: What It Costs and What Actually Fails

Mr-Glass kitchen remodeling in The Hammocks typically runs $14,000 – $45,000 for a full install, with cabinet refacing and door replacement landing lower and full cabinet-plus-countertop builds at the top of the range. The parts that fail first on a Mr-Glass system are the hinges, drawer glides, and cabinet box fasteners: hardware rated for a dry European climate, installed in a Hammocks kitchen with year-round humidity and afternoon thunderstorms, tends to loosen and corrode faster than the door face ever does.

Call (844) 761-9356

Most owners don’t find out something’s wrong until a hinge snaps, a drawer won’t close flush, or a cabinet door sags off its top mount. You open the door one morning and it hangs at an angle. The part behind it, not the door itself, is almost always the culprit.

Groundwork Construction Co. of The Hammocks is an independent service provider, not affiliated with Mr-Glass. We source and install compatible parts and handle the full remodel when the failing part is a symptom of something bigger.

Which Mr-Glass Models and Systems This Applies To

Mr-Glass covers a wide line of cabinet and kitchen systems, and the part that fits one series won’t always fit another. The good news: the identifying information is stamped on the cabinet box interior, usually on the inside wall or the underside of the top rail. Look for the model sticker before you measure anything. Series numbers on Mr-Glass cabinetry sit in a four- to six-digit range, and the hinge and glide pattern changes between series, so a part pulled from Series A won’t seat properly in Series B even when the door dimensions look identical.

Measure the door width, door height, and the distance between hinge bore centers. Write those three numbers down. A cabinet door that measures 14-3/16 inches wide and 20-1/2 inches tall uses a different hinge cup offset than the 15-inch version of the same series, and that difference of a fraction of an inch is enough to leave a gap at the top of the door when it closes.

On the OEM-versus-aftermarket call: Mr-Glass OEM parts are the safest match for fit and finish, but quality aftermarket equivalents for hinges and glides are widely available and often more durable because they’re built to the same European hinge standard that Mr-Glass itself follows. The decision usually comes down to whether you need the exact finish match or you need a hinge that holds up in Florida humidity. We don’t carry a stock of parts and don’t have parts on a truck; every part we install is sourced specifically for your model and ordered before the job date.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Mr-Glass Kitchen Remodeling Is Failing

  • A cabinet door that won’t stay closed or sits crooked. The hinge is usually the cause, not the door. The self-closing spring inside a soft-close hinge loses tension after a few thousand cycles, and the door drifts open on its own.
  • Drawers that scrape or bind when you pull them. The glide is worn or the cabinet box has swollen from moisture. South Florida humidity causes particleboard and composite cabinet sides to expand, and a swollen box will bind even a new glide.
  • Visible rust or white corrosion on hinge plates. The Hammocks sits close enough to the coast that salt air reaches interior hardware over a few years. Cheap steel hinges start rusting at the screw heads and the cup edge first.
  • Doors that sag at the top corner. The screws holding the hinge plate have stripped out of the cabinet wall. This is a fastener failure, and it’s directional: a stripped hole in a solid wood box can be repaired, but a stripped hole in MDF usually means replacing the affected cabinet section.
  • Water damage or soft spots around the sink cabinet base. That’s a cabinet box failure, not a parts failure. At that point you’re pricing a cabinet install ($4,000 – $13,000 in The Hammocks), not a hinge swap.

Replacement Cost in The Hammocks and What’s Included

Pricing for Mr-Glass kitchen work in The Hammocks breaks into these installed ranges. All of them cover parts plus labor, with upfront pricing so the number you see is the number you pay.

Scope Installed Range (The Hammocks)
Small kitchen remodel $9,000 – $20,000
Full kitchen remodel $14,000 – $45,000
Cabinet installation $4,000 – $13,000
Countertop installation $2,000 – $6,500
Backsplash installation $800 – $2,500
Kitchen island installation $3,000 – $10,000

What drives the range: number of cabinet boxes, door style and finish, countertop material, and whether the job involves moving plumbing or electrical. A single hinge or glide replacement sits well below these scopes and is priced as a service call. Every project is covered by our 730-Day Done Right Promise. If the install isn’t right, we come back and make it right.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

DIY or Call Us?

A few things are safe to check on your own. Open the cabinet door and look at the hinge cup screws. Are they loose? Can you tighten them with a Phillips head? Does the door close flush when you lift it slightly? If the answer to those questions points to a loose screw and a hinge that’s still intact, tightening it is a five-minute job and you’re fine to do it.

Where DIY goes wrong: replacing a hinge, re-boring a stripped screw hole, or adjusting a soft-close mechanism that’s failed internally. The hinge positions have to be exact, the screw holes have to be drilled at the right depth, and an over-tightened screw strips the cabinet wall. Once a cabinet wall is stripped, the repair cost jumps from a hinge swap to a cabinet repair. If the door is sagging off the box or the hinge is visibly broken, call us.

If you’re not sure whether it’s a hinge or a cabinet box problem, call (844) 761-9356 and we’ll walk you through it.

FAQs

Ready to Get a Real Number?

If you’re pricing a Mr-Glass kitchen fix in The Hammocks or you’re ready to move on a full remodel, call us at (844) 761-9356 for a free estimate. We’ll walk the kitchen, tell you honestly whether you’re looking at a hinge swap or a cabinet replacement, and give you a written range up front. Calls are answered by a live person 24/7. We also service KraftMaid, Cambria, and Silestone installs in The Hammocks and the surrounding neighborhoods.

Written by the team at Groundwork Construction Co. of The Hammocks, serving The Hammocks and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 761-9356
Local Service Coverage

Request a Free Estimate in The Hammocks

Tell us what you need - Groundwork Construction Co. of The Hammocks responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch