Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Home Additions & ADU: The The Hammocks Owner’s Guide
We build Moen-plumbed home additions and ADUs in The Hammocks, and a full addition typically runs $45,000 – $130,000 installed, with detached ADUs landing at $90,000 – $220,000. We don’t promise same-day construction because nobody builds an addition in a day, but we do give you a written line-item estimate and answer the phone live at (844) 761-9356 whenever you call. Most The Hammocks owners we work with discover a problem the same way: a slow drip behind a new vanity, a shower valve that won’t hold temperature, or a Moen rough-in that was set at the wrong depth during a prior renovation. Groundwork Construction Co. of The Hammocks is an independent builder, not affiliated with Moen.
Which Moen Models This Applies To
Moen isn’t one valve; it’s a family of them, and the series determines what fits. The most common valves we encounter in The Hammocks additions are the 1222 cartridge (single-handle faucets), the 1225 (Posi-Temp tub and shower), and the 1200/1200B (older two-handle systems). Newer builds often use the M-CORE 3 or 4 series rough-in, which uses a completely different cartridge body than the legacy 1222 – a compatibility trap that bites homeowners who order the wrong part online.
To identify yours, pull the handle and trim plate and read the stamped number on the cartridge face, or find the model number on the faucet escutcheon. When measurements matter, note the cartridge length and the valve body diameter before you order.
On the OEM-versus-aftermarket question, Moen’s own cartridges carry the correct tolerances and the ceramic-disc finish that generic equivalents often approximate poorly. For a permanent addition where you’ll live with that fixture for decades, OEM is the right call. Quality aftermarket is fine for a temporary fix; it isn’t what we specify in a finished build. We also source KraftMaid, Cambria, and Silestone for the finishes around those fixtures.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Home Additions & ADU Is Failing
- Dripping from the spout when the handle is off. Worn rubber seats or a scored ceramic cartridge – the classic 1222 failure after years of The Hammocks’ hard water.
- Handle feels stiff or grinds. Mineral buildup inside the cartridge bore, common in homes on well water or older municipal lines.
- Water temperature won’t hold. A failing Posi-Temp pressure-balancing spool, which can scald if ignored.
- Water pooling at the rough-in. A valve body set too shallow during a prior remodel, letting moisture wick behind the tile – costly to catch late.
- Reduced flow at the showerhead. Clogged cartridge ports or a failing diverter, not just a dirty aerator.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fixture swaps and Moen rough-in corrections inside a home addition or ADU in The Hammocks are folded into the broader addition budget of $45,000 – $130,000, with plumbing line items running typically $3,500 – $12,000 depending on how many fixtures, how much re-piping, and whether we’re opening a finished wall. The range moves on access difficulty, permit requirements, and whether we’re correcting a prior installer’s work. Every estimate is written line-item and fixed – the number you see is the number you pay, with $1,000 off projects over $10,000 and 0% financing for 18 months available. All workmanship is covered by our 730-Day Done Right Promise; if it’s not done right, we make it right. We don’t stock parts or carry them on trucks – we source what the job needs.
DIY or Call Us?
You can safely shut off the supply, remove a faucet handle, photograph the cartridge, and read the stamped model number. That’s where DIY usually stops being safe. Opening a wall to correct a rough-in, re-sweating a copper line, or swapping a valve body inside a finished shower is plumbing work where a mistake means water damage behind tile – and behind the tile in a brand-new The Hammocks addition, that’s an expensive recovery. We recommend a licensed plumber for anything past the trim. Call (844) 761-9356 for a free estimate and we’ll tell you honestly whether it’s a 30-minute swap or a wall-open job. Our technicians have up to 12 years of experience.
FAQs
How long does a Moen cartridge last? A genuine Moen cartridge typically lasts 8 – 12 years in South Florida’s water; hard water in The Hammocks can shorten that. Call (844) 761-9356 for an exact quote on replacement – estimates are free.
Can the part be repaired instead of replaced? Sometimes – a worn seat or O-ring can be swapped without a full cartridge change, but a scored ceramic disc cannot be repaired and must be replaced. We’ll tell you which you’re facing on the first visit.
How long does the swap take? A standard cartridge replacement is 30 – 60 minutes; a valve body correction inside a finished wall is a half-day or longer. Exact timing depends on access – call for a quote.
How do you source the part? We match the exact Moen series to your valve, order OEM or a specified equivalent, and schedule installation around the delivery. No guesswork, no generic substitutes on a finished build.
Ready for a written estimate on your Moen addition or ADU in The Hammocks? Call (844) 761-9356 – a live person answers 24/7, and your estimate and design consult are free.
Written by the team at Groundwork Construction Co. of The Hammocks, serving The Hammocks and nearby areas.