Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why The Hammocks Homeowners Choose CGI Construction
Groundwork Construction Co. of The Hammocks provides independent CGI construction service across The Hammocks, FL – cabinet installation and refacing, quartz and stone countertops, and standing seam metal roofing. What makes our CGI work different is that we’ve installed these products across South Florida and we know how they fail here: RTA joints that loosen in the humidity, quartz edges that chip when the substrate is wrong, roof panels that back out after a wind season. We’re an independent construction firm, not authorized, sponsored, or endorsed by CGI. Our technicians have up to 12 years of experience, all work is covered by our 730-Day Done Right Promise, and calls are answered by a live person, 24/7. Reach us at (844) 761-9356.
Why Trust Groundwork Construction Co. of The Hammocks for Your CGI Construction?
CGI products have quirks that generic installers learn the hard way. The Ready-to-Assemble cabinet line arrives as flat boxes with cam locks and particleboard cores, and the difference between a cabinet that lasts fifteen years and one that fails in three is whether the assembler torqued the fasteners correctly, glued the dowels, and squared the frame. We do all three. On the countertop side, CGI’s quartz slabs need a flat, fully supported substrate before adhesive goes down, or the resin edge chips within a season. On roofing, the CGI metal panel systems – standing seam and exposed-fastener – live or die on fastener selection and UV-stable sealant, not on the panel itself.
We source CGI OEM replacement parts – hinges, drawer glides, door fronts, panel trims, roofing fasteners – whenever they’re available, so the fit and finish stay intact. For discontinued items we use vetted aftermarket equivalents and tell you plainly which is which. Every repair is quoted against the cost of a full replacement, in writing, with upfront pricing. A 730-Day Done Right Promise covers the workmanship either way. We’re not a CGI dealer and we don’t pretend to be one – we’re an independent installer who’s watched these products perform in The Hammocks’ climate long enough to know what holds and what doesn’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common CGI Construction Problems We Fix in The Hammocks
The Hammocks is a 1980s-to-2000s tract subdivision, mostly concrete-block homes with stucco and tile roofs, and the second-generation cycle is in full swing. Here’s what we see on CGI products specifically.
- RTA cabinet joints pulling apart and doors sticking. The CGI Shaker and Flat Panel door styles have particleboard cores, and in South Florida’s humidity those cores swell at the joints. The usual root cause is under-torqued assembly screws from the original build combined with non-corrosion-resistant hardware that has started to fail silently. Doors stick, frames separate, and by the time a homeowner notices, the box itself has begun to deform.
- Quartz countertop edge chipping and seam separation. CGI’s Stone and Quartz Collection is engineered quartz, and it’s hard but brittle at the edge. When the substrate underneath is uneven, or the adhesive isn’t rated for temperature swing, the seam opens and the edge chips at the sink cutout. Florida rooms and lanais that fluctuate between conditioned and unconditioned air are the usual offenders.
- Metal roof panel micro-cracking and fastener back-out. CGI standing seam and exposed-fastener systems take a beating in hurricane season. Wind uplift works fasteners loose, and where panels were cut short or sealant wasn’t UV-stable, the sealant degrades after a couple of summers. Micro-cracks appear along the bends and moisture gets in.
- Cabinet door warping and finish delamination. Lower-end CGI lines exposed to steam from an unvented bathroom or a kitchen without a properly sized exhaust fan will warp and delaminate. The finish lifts first at the bottom edges, closest to the moisture source.
- Bathroom vanity water damage. CGI’s wood and composite vanities with ceramic sinks fail at the toe kick and side panels first, where slow leaks and condensation collect. Composite holds up better than wood, but both suffer when the caulk line behind the sink has gone.
None of these are brand defects in the strict sense. They’re installation and ventilation issues, and they’re fixable when they’re caught early.
CGI Parts & Our Repair-vs-Replace Approach
We don’t claim to stock CGI parts locally, and any contractor who tells you they do is guessing. What we do is source them per job: OEM hinges, drawer glides, door fronts, panel trims, and roofing fasteners when they’re still in production, and vetted aftermarket equivalents for discontinued items. We tell you which you’re getting before we order.
Repair versus replace comes down to the box, not the door. If the cabinet frame is sound and only the fronts are damaged, we reface. If the particleboard has swelled past recovery, we replace that cabinet run and leave the rest. On quartz, a chipped edge can often be repaired or re-profiled; a separated seam over a failed substrate usually means pulling the slab and fixing what’s underneath. On metal roofs, isolated back-out is a refasten-and-reseal job; micro-cracking across multiple panels points to replacement. Every call is a written line-item quote with no change orders. Call (844) 761-9356 for an honest assessment – estimates are free.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We inspect the actual CGI installation – cabinet boxes, hardware torque, substrate flatness under quartz, fastener condition and sealant on metal panels – not just the visible symptom.
- 2
Written scope and quote. Line-item pricing on the repair or installation, with the OEM-versus-aftermarket parts choice spelled out and the 730-Day Done Right Promise attached.
- 3
Repair or install. Re-squaring and re-fastening cabinet frames with corrosion-resistant hardware; setting quartz on a properly supported substrate with appropriate adhesive; installing or re-securing metal panels with UV-stable sealant and correct fasteners for the Miami-Dade wind requirements.
- 4
Test and walkthrough. Doors open and close under load, seams get probed, roof panels get checked at every fastener. We don’t hand off until it’s right.
- 5
Warranty and follow-up. The 730-Day Done Right Promise covers workmanship in writing. If it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in The Hammocks
We cover the CGI lines that dominate local homes: Ready-to-Assemble kitchen cabinets in Shaker and Flat Panel door styles, the Stone and Quartz Countertop Collection (engineered quartz and natural stone), the Metal Roofing Systems in both standing seam and exposed-fastener panels, and the bathroom vanity and fixture lines, including wood and composite vanities with ceramic sinks. Cabinet installation and refacing, quartz and granite countertops, and standing seam metal roofs are the three services we’re called for most in The Hammocks. Because these homes were built in a narrow window, whole blocks tend to need the same work at the same time – a neighbor’s tile re-roof or impact-window permit often triggers a run of CGI cabinet and countertop jobs down the street.
We Also Service These Brands
CGI is one line in a much bigger toolbox. Groundwork Construction Co. of The Hammocks also works with KraftMaid cabinetry, Cambria and Silestone quartz, and Kohler fixtures – and our full service range runs from kitchen and bathroom remodeling to roofing, windows and doors, fencing, driveways and pavers, and home additions and ADUs. When we quote a job, you’re getting the right product for the space, not the only brand we carry.
FAQs – CGI Construction Service in The Hammocks
Is Groundwork Construction Co. of The Hammocks authorized by CGI? No. We’re an independent construction firm, not authorized, sponsored, or endorsed by CGI. We’ve installed their products across South Florida and we service them as an independent provider.
Do you use genuine CGI/OEM parts? Yes, when they’re available. We source OEM hinges, drawer glides, door fronts, panel trims, and roofing fasteners to preserve the original fit and finish, and we use vetted aftermarket equivalents only for discontinued items – always disclosed before we order.
How long does CGI service take? A cabinet hardware or door-refacing job is often a single visit. A quartz countertop replacement runs one to two days once the slab is on site. A metal roof or full cabinet run depends on the scope and permitting, and we tell you the timeline in the written quote before work starts.
What CGI models/series do you cover? The Ready-to-Assemble kitchen cabinets in Shaker and Flat Panel styles, the Stone and Quartz Countertop Collection, the Metal Roofing Systems in standing seam and exposed-fastener panels, and the bathroom vanity and fixture lines.
Will service void my CGI warranty? Proper installation and OEM parts keep you inside the manufacturer’s terms. Damage from an improper install can void coverage, which is why we follow the installation specs and use specified fasteners and adhesives. We’ll flag anything in your current installation that may already have compromised coverage.
How much does CGI construction cost in The Hammocks? It depends on the scope. Cabinet installation runs $4,000 – $13,000; countertop installation $2,000 – $6,500; standing seam metal roofing $15,000 – $40,000; a small kitchen remodel $9,000 – $20,000; and bathroom vanity installation $800 – $3,000. The typical job: a homeowner notices CGI Shaker doors sticking and frames separating after a few humid summers, and the fix is inspecting the boxes, replacing damaged panels, re-squaring and re-fastening with corrosion-resistant hardware, then addressing ventilation. Call (844) 761-9356 for an exact quote – estimates are free.
Book Your CGI Service in The Hammocks, FL
Whether it’s CGI RTA cabinets, a chipped quartz edge, or a metal roof that’s seen one hurricane too many, we’ll diagnose it honestly and quote it in writing. No-hassle upfront pricing, 0% financing for 18 months, and $1,000 off projects over $10,000. Call (844) 761-9356 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of The Hammocks.